Skip to content | Skip to institutional links

Common menu bar links

Institutional links

Air Transportation

Browse Air Resources

Air Contact Information

National Headquarters

Browse By Mode

Browse By Subject

About Us

About Transport Canada

Project Management (Certification of Aeronautical Products)

Type Certification Application

This form is also available in Microsoft Word Document format (55 KB) which will download in approximately 15 seconds on a 28.8 connection and may be viewed using Microsoft Word or a Microsoft Word Viewer. Visit the Microsoft Office download center to acquire a free download of Word 97/2000 Viewer (Word 2000) (Windows 95/98/NT).

Type Certification Application for Foreign Designed Aircraft, Engines and Propellers (Foreign Products)

PART I - GENERAL INFORMATION

Before submitting an application for the issue of a type certificate for a foreign aeronautical product, applicants are urged to take note of the provisions contained in Canadian Aviation Regulations, Part V, Subpart 11, Airworthiness Manual Chapter 511, particularly sub-Chapter C and Airworthiness Manual Advisory 511/2. This information can be found on the Transport Canada internet site at: http://www.tc.gc.ca/civilaviation/regserv/affairs/cars/menu.htm.

1. Name and address of applicant.

Telephone:
E-mail:
Facsimile:

2. Name and address of airworthiness contact person (if different from 1).

Telephone:
E-mail:
Facsimile:

3. Name and address for billing purposes (if different than 1).

Telephone:
E-mail:
Facsimile:

4. Identification of the product.

5. The applicant is responsible for the control of product manufacture.

YES		NO

If no, provide details.

6. Design changes approved under Supplemental Type Certificates are included in the current configuration for certification.

YES		NO

If yes, provide a list.

7. The applicant is requesting a simultaneous review for compliance with the Canadian Design-Related Operational Requirements. (Specify)

YES		NO

If yes, specify.

PART II - DOCUMENTATION

8. The following documentation is hereby submitted, or will be submitted in support of this application: (Specify) (Use attachments where necessary.)
Submitted	To Be Sumbmitted
		Proof of a Canadian customer; i.e. a bill of sale or letter of intent to purchase.
		A statement of the basis of type design certification applied by the Exporting Airworthiness Authority, including copies of any special conditions, and the date of application for domestic type design certification.
		A statement detailing, and copies of, any exemptions from, or findings of equivalent safety with, the applicant's domestic airworthiness standards for the aircraft, engine and propeller as certified.
		The type certification document or equivalent for the aircraft, engine and propeller, including any supporting airworthiness documents or equivalent, issued by the Exporting Airworthiness Authority.
		General description of the product, including: for an aircraft, a three view drawing; for an engine or propeller, operating characteristics and proposed operating limitations.
		The approved Flight Manual, the portions of the Maintenance Manual or equivalent document which contains the Airworthiness Limitations, the Installation Manual, the Instructions for Continued Airworthiness and the Recommended Scheduled Maintenance Program (as appropriate).
		Airworthiness Directives, or their equivalent, applicable to the aircraft, engine or propeller.
		A statement of compliance with Airworthiness Manual Chapter 516 (Airworthiness Standards, Aircraft Emissions).
		The approved Master Minimum Equipment List (where appropriate).
		Other (specify).

9. Applicant's additional information.

10. I hereby certify that the information contained herein is correct and complete. I agree to pay all charges imposed in respect of the issuance, renewal, amendment or endorsement of a type certificate for an aeronautical product and to reimburse Transport Canada for incremental costs associated with the processing of applications outside Canada in accordance with the provisions contained in the Canadian Aviation Regulations Part I, Subpart 4.

______	___________________________________________	__________________________
DATE	NAME AND SIGNATURE OF COMPANY OFFICIAL	COMPANY TITLE/POSITION

PART III - TO BE COMPLETED BY THE EXPORTING AIRWORTHINESS AUTHORITY BEFORE SUBMITTING TO TRANSPORT CANADA

11. Any correspondence relating to this Transport Canada certification project may be forwarded to the following airworthiness authority officials:

NAME:

TITLE:

AIRWORTHINESS AUTHORITY:

ADDRESS:

|
|
|
|
|
|
|

TELEPHONE:

E-MAIL:

FACSIMILE:

It is hereby certified that the statement concerning the basis of certification, deviations, exemptions or differences as specified in applicable items listed under Part II Section 8 are correct and complete, except for the following:

N/A

_________	_____________________________________________________________________________
DATE	SIGNATURE OF EXPORTING AIRWORTHINESS AUTHORITY OFFICIAL

When Parts I, II and III have been completed, submit to:

Transport Canada
Aircraft Certification (AARDE)
Place de Ville, Tower C
330 Sparks St., 3rd Floor
Ottawa ON K1A 0N8