Standard Seat Assembly Specifications for Motor Vehicle Restraint Systems and Booster Seats Safety Regulations Compliance Testing

From: Transport Canada

Issued: January 1, 2010

Standards Research and Development Branch
Motor Vehicle Safety Directorate
TRANSPORT CANADA
Ottawa, Ontario
K1P 5H9

 

 

Unless otherwise specified, all dimensions are in mm and inches

 

Tolerances shall not be cumulative

MM:
0 to 12.7mm ± 0.79mm
12.7 to 25.4mm ± 1.580mm
25.4 to 127mm ± 3.175mm
127 to 254mm ± 6.35mm

FRACTIONS:
0 to 1/2 ± 1/32
1/2 to 1 INCL ± 1/16
1 to 5 INCL ± 1/8
5 to 10 INCL ± 1/4

 

Remove all burrs. Break
sharp edges .12700mm - .38100mm
sharp edges .005 to .015 INCHES

 

 

DRAWING PACKAGE: STANDARD SEAT ASSEMBLY SPECIFICATIONS FOR MOTOR VEHICLE RESTRAINT SYSTEMS AND BOOSTER SEATS SAFETY REGULATIONS COMPLIANCE TESTING
NAME DRAWING SHEET NUMBER DATE
SEAT ASSEMBLY 2010SSA100 01/01/2010
   
   
FRAME, ASSEMBLY 2010SSA200 01/01/2010
   
   
FRAME, FRONT AND SIDE ASSEMBLY 2010SSA201 01/01/2010
   
   
FRAME, BOTTOM ASSEMBLY 2010SSA202 01/01/2010
   
   
FRAME, SEAT TOP ASSEMBLY 2010SSA203 01/01/2010
   
   
ANCHOR POINTS ASSEMBLY 2010SSA204 01/01/2010
   
   
FRAME, BACK ASSEMBLY 2010SSA205 01/01/2010
   
   
CUSHION, ASSEMBLY 2010SSA300 01/01/2010
   
   
CUSHION, SEAT ASSEMBLY 2010SSA301 01/01/2010
   
   
CUSHION, BACK ASSEMBLY 2010SSA302 01/01/2010
   
   
BACKING, SEAT AND BACK ASSEMBLY 2010SSA303 01/01/2010
   
   

2010SSA100 – Seat Assembly

 


SIDE VIEW

 

 

FRONT VIEW

 

 


FRONT VIEW

 

Notes:

  1. Dimensions in mm
  2. Drawing is not to scale.

Parts List:

[6]. Bar assembly
[7]. Frame, assembly
[8]. Cushion assembly

2010SSA200 – Frame, Assembly

 

Notes:

  1. All dimensions are in mm except for parts, diameters, and welds, which are in inches.
  2. Drawing is not to scale.
  3. Pivot Block [25] should be free to rotate with Shoulder Bolt [10] installed.
  4. Rigid Rod [28] shall be replaced after each test.
  5. Round HD Screw [15] and HEX Nut [16] shall be assembled to Frame, Seat Top Assembly [4] and Frame, Back Assembly [5] before cushion installations in 20 places.
  6. Use 125% safety factor for all welds, electric weld with 3/32 Fleetwood 3T Rod. Weld all places possible at junctions of tube and plates. Welded assemblies may be painted for appearance and corrosion protection.
  7. Grind welds flush on top and bottom surfaces of seat base weldment.

Parts:

[1]. Frame, Assembly
[2]. Frame, Front and Side Assembly
[3]. Frame, Bottom Assembly
[4]. Frame, Seat Top Assembly
[5]. Frame, Back Assembly
[10]. Shoulder Bolt, 1/2 SOC. HD Bolt. See detail A.
[11]. Bearing (4 places)
[12]. HEX Head Bolt, 3/8-16 NC-2 X 2-1/2 LG
[13]. HEX Nut, 3/8-16 NC-2
[14]. HEX Head Bolt, 3/8-16 NC-2 X 3-1/2 LG
[15]. Round HD Screw, 1/4-20 NC-2 X 2
[16]. HEX Nut, 1/4-20 NC-2
[17]. Round HD Screw, 1/4-28 NF-2-1-1/2 LG
[18]. HEX Nut, 1/4-28 NF-2
[19]. Outboard Belt Anchor Bracket, steel, 2 X 2 X 2.25 X 3
[20]. Inboard Belt Anchor Bracket, steel, 1/4 X 1-1/4 X 3-1/4
[21]. Pillow Block, steel
[22]. Seat Anchor Front, steel
[23]. Gusset, steel
[24]. Steel Plate
[25]. Pivot Block, steel
[26]. Seat Anchor Back, steel
[27]. Dynamic Tuning Block, steel
[28]. Rigid Rod, 1045 Cold Rolled steel
[29]. Rod, steel

 

 

 

 

 

 

 

 

 

 

2010SSA201 - Frame, Front and Side Assembly

 

 

  1. Dimensions in mm except for welds, which are in inches.
  2. Drawing is not to scale.
  3. Use 125% safety factor for all welds, electric weld with 3/32 Fleetwood 3T Rod. Weld all places possible at junctions of tube and plates. Welded assemblies may be painted for appearance and corrosion protection.
  4. Grind welds flush on top and bottom surfaces of seat base weldment.

Parts List:

[1]. Frame, Front Assembly
[2]. Frame, Side Assembly
[7]. Tubing, steel, 15ga. 1 sq. cut lg. = 254.00 mm
[8]. Tubing, steel, 15ga. 1 sq. cut lg. = 558.80 mm
[9]. Tubing, steel, 15ga. 1 sq. cut lg. = 139.70 mm
[10]. Tubing, steel, 15ga. 1 sq. cut lg. = 165.10 mm
[11]. Tubing, steel, 15ga. 1 sq. cut lg. = 92.07 mm
[12]. Frame, Bottom Assembly
[13]. Frame, Seat Top Assembly

2010SSA202 - Frame, Bottom Assembly

 

  1. Dimensions in mm except for welds, parts, diameters which are in inches.
  2. Drawing is not to scale.
  3. Use 125% safety factor for all welds, electric weld with 3/32 Fleetwood 3T Rod. Weld all places possible at junctions of tube and plates. Welded assemblies may be painted for appearance and corrosion protection.
  4. Grind welds flush on top and bottom surfaces of seat base weldment.

Parts List:

[1]. Frame, Bottom Assembly
[6]. Inboard Belt Anchor Bracket
[7]. Seat Anchor Front
[8]. Gusset
[9]. Steel Plate
[10]. Seat Anchor Back
[11]. Tubing, steel, 15ga. 1 sq. cut lg. = 762.00 mm
[12]. Tubing, steel, 15ga. 1 sq. cut lg. = 685.80 mm
[13]. Tubing, steel, 15ga. 1 sq. cut lg. = 1270.00 mm
[14]. Tubing, steel, 15ga. 1 sq. cut lg. = 552.45 mm
[15]. Tubing, steel, 15ga. 1 sq. cut lg. = 50.80 mm
[16]. Tubing, steel, 15ga. 1 sq. cut lg. = 1066.80 mm

2010SSA203 – Frame, Seat Top Assembly

 

 

Notes:

  1. Dimensions in mm except for welds, parts, diameters which are in inches.
  2. Drawing is not to scale
  3. Use 125% Safety Factor for all welds, electric weld with 3/32 Fleetwood 3T Rod. Weld all places possible at junction of tube and plates. Welded assemblies may be painted for appearance and corrosion protection.
  4. Grind welds flush on top and bottom surfaces of seat base weldment.
  5. .265 DIA holes shall be drilled in Frame, Seat Top Assembly [1] for attachment of Cushion, Seat Assembly  in 6 places.

Parts List:

[1]. Frame, Seat Top Assembly
[6]. Tubing, steel, 15ga. 1 sq. cut lg. = 1270.00 mm
[7]. Tubing, steel, 15ga. 1 sq. cut lg. = 558.80 mm
[8]. Tubing, steel, 15ga. 1 sq. cut lg. = 1130.30 mm
[9]. Tubing, steel, 15ga. 1 sq. cut lg. = 1066.80 mm
[10]. Tubing, steel, 15ga. 1 sq. cut lg. = 660.40 mm
[11]. Tubing, steel, 15ga. 1 sq. cut lg. = 165.10 mm
[12]. Tubing, steel, 15ga. 1 sq. cut lg. = 50.80 mm
[13]. Tubing, steel, 15ga. 1 sq. cut lg. = 635.40 mm
[14]. Tubing, steel, 15ga. 1 sq. cut lg. = 95.25 mm
[15]. Tubing, steel, 15ga. 1 sq. cut lg. = 171.45 mm
[16]. Tubing, steel, 15ga. 1 sq. cut lg. = 247.65 mm
[17]. Bar, steel, 1 X 1, cut lg. = 165.10 mm
[18]. Bar, steel, 1 X 1, cut lg. = 95.25 mm
[19]. Bar, steel, 1 X 1, cut lg. = 101.60 mm
[20]. Plate, steel, 1/4 X 3.75 X 6 in
[21]. Plate, steel, 3/8 X 4.75 X 6 in
[22]. Plate, steel, 3/8 X 5 X 5.75 in
[23]. Plate, steel, 1/4 X 4 X 5 in

2010SSA204 – Anchor Points Assembly

 

 

 

Notes:

  1. Dimensions in mm except for welds, parts, diameters which are in inches.
  2. Drawing is not to scale.
  3. Use 125% Safety Factor for all welds, electric weld with 3/32 Fleetwood 3T Rod. Weld all places possible at junctions of tube and plates. Welded assemblies may be painted for appearance and corrosion protection.
  4. Grind welds flush on top and bottom surfaces of seat base weldment.
  5. Lower Universal Anchor Bars: 6 mm DIA, 25 mm length, located 102 mm forward of point Z and 323 mm upward from floor.
  6. .531 DIA holes 6 places for Seat Base Attachment to test fixture.
  7. 1/2 Threaded Rod [17] is recommended with Belt Clevis and Nut [16] to simplify belt tensioning adjustment at both Inboard and Outboard Belt Anchors.
  8. 2 Nuts [16] are required to be used with Inboard Belt Anchor Bracket [11]. If the Outboard Belt Anchor Bracket [10] is used, 2 more Nuts [16] are required.
  9. Maximum distance from the seat bight to the end of the belt buckle is 175 mm.

Parts List:

[1]. Anchor Points Assembly
[6]. Frame, Front Assembly
[7]. Frame, Side Assembly
[8]. Frame, Bottom Assembly
[9]. Frame, Seat Top Assembly
[10]. Outboard Belt Anchor Bracket
[11]. Inboard Belt Anchor Bracket
[12]. Seat Anchor Front
[13]. Gusset
[14]. Steel Plate
[15]. Seat Anchor Back
[16]. Nut, steel, 1-1/8 DIA X 1/2 TK.
[17]. Rod, Threaded Rod, 1/2 DIA

2010SSA205 – Frame, Back Assembly

 

 

 

Notes:

  1. Dimensions in mm except for parts, diameters, and welds, which are in inches.
  2. Drawing is not to scale.
  3. Use 125% Safety Factor for all welds, electric weld with 3/32 Fleetwood 3T Rod. Weld all places possible at junctions of tube and plates. Welded assemblies may be painted for appearance and corrosion protection.
  4. Grind welds flush on top and bottom surfaces of seat base weldment.
  5. .265 DIA holes shall be drilled 15 places in Frame, Back Seat Assembly [1] for attachment of Cushion, Back Assembly.
  6. Slotted holes shall be placed in the back of Frame, Back Assembly [1] for attachment of Dynamic Tuning Block, 4 places. See Detail B.

Parts List:

[1]. Frame, Back Assembly
[6]. Tubing, steel, 15ga. 1 sq. cut lg. = 1276.35 mm
[7]. Tubing, steel, 15ga. 1 sq. cut lg. = 749.30 mm
[8]. Tubing, steel, 15ga. 1 sq. cut lg. = 622.30 mm
[9]. Tubing, steel, 15ga. 1 sq. cut lg. = 1143.00 mm
[10]. Tubing, steel, 15ga. 1 sq. cut lg. = 641.35 mm
[11]. Tubing, steel, 15ga. 1 sq. cut lg. = 69.85 mm
[12]. Tubing, steel, 15ga. 1 sq. cut lg. = 127.00 mm
[13]. Tubing, steel, 15ga. 1 sq. cut lg. = 196.85 mm
[14]. Bar, steel, 1 X 1, cut lg. = 88.90 mm
[15]. Plate, steel, 1/4 X 1 X 6.50 in
[16]. Plate, steel, 1/4 X 5 X 6.00 in
[17]. Rod, steel, 1 DIA lg. = 4.00 in

2010SSA300 – Cushion, Assembly

 

Notes:

  1. Foam shall measure 54 X 24 X 6 inches. One or two pieces of foam may be used to achieve required dimension.
  2. To be suitable for compliance testing, foam inserts shall compress 25% under the following load limits:
    51 mm (2 in) thick foam: 20.4 to 24.9 kg (45 to 55 lbs)
    102 mm (4 in) thick foam: 9.5 to 12.2 kg (21 to 27 lbs)

Parts List:

[1]. Cushion, Assembly
[6]. Cushion, Seat Assembly
[7]. Cushion, Back Assembly

SPECIFICATIONS, SEATING FOAM POLYURETHANE FOAM A FOAM B
DESCRIPTION EXTRA FIRM HIGH DENSITY GRADE MEDIUM SOFT GRADE
DENSITY – PCF 2.70 ± .10
*INDENT LOAD – LBS. – 4 THK @ 25% DEFLECTION 45 – 55 21 – 27
INDENT LOAD RATIO (65/25) – MIN 2.0 1.9
TENSILE – PSI – MIN 12 12
ELONGATION - % - MIN 175 175
TEAR RESISTANCE – LBS/IN – MIN 1.75 1.75
COMPRESSION SET METHOD B – ORIGINAL – 50% MAX 15.0  
22 HRS. @ 58o F – 90% - MAX   20.0
HUMIDITY AGED 5 HRS. @ 250o F 50% MAX 20.0 20.0
90% MAX   20.0

* AS PER METHOD B1 OF ASTM STANDARD d3574-08 Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams

 

FOAM POSITION FOAM TYPE X Y Z
SEAT BACK LOWER (AGAINST PLYWOOD BACKING) A 24 54 2
SEAT BACK UPPER B 24 54 4
SEAT BASE LOWER (AGAINST PLYWOOD BACKING) A 20 54 2
SEAT BASE UPPER B 20 54 4

2010SSA301 – Cushion, Seat Assembly

 

Notes:

  1. Dimensions in mm except for parts which are in inches.
  2. Drawing is not to scale.
  3. Punch 6 holes .28 DIA on back of [6] to allow protrusion of screws (match to Backing, Seat Assembly).
  4. [6] shall be elastic back automotive upholstery vinyl.
  5. [10] shall be 100 inches long and run around 3 sides of [6].
  6. Stitching as described in ASTM D6193-09 Standard Practice for Stiches and Seams, stitch type 301, 6 to 8 SPL.

Parts List:

[1]. Cushion, Seat Assembly
[6]. Cover, Cushion
[7]. Foam, Cushion
[8]. Backing, Cushion .38 plywood
[9]. Thread, (stitching) V-T-295-E
[10]. Slide Fastener VF-106

2010SSA302 – Cushion, Back Assembly

 

 

Notes:

  1. Dimensions in mm except for parts which are in inches.
  2. Drawing is not to scale.
  3. Punch 15 holes .28 DIA on back of [6] to allow protrusion of screws.
  4. [6] shall be elastic back automotive upholstery vinyl.
  5. [10] shall be 100 inches long and run around 3 sides of cover.
  6. Stitching as described in ASTM D6193-09 Standard Practice for Stiches and Seams, stitch type 301, 6 to 8 SPI.

Parts List:

[1]. Cushion, Back Assembly
[6]. Cover, Cushion; Vinyl; Automotive upholstery
[7]. Foam, Cushion
[8]. Backing, Cushion .38 plywood
[9]. Thread, (stitching) V-T-295-E
[10]. Slide Fastener VF-106
[11]. Grommets

2010SSA303 – Backing, Seat and Back Assembly

 

Notes:

  1. Dimensions in mm except for parts and diameters, which are in inches.
  2. Drawing is not to scale.
  3. It is recommended that the Frame, Seat Top Assembly be used as a template to drill holes. [1] shall be clamped in position on Frame, Seat Top Assembly, in order to drill holes to match. Use a .281 DIA hole or a size for light press fit to the neck of the "T" Nut [11].
  4. It is recommended that the Frame, Back Assembly be used as a template to drill holes. [1] shall be clamped in position on Frame, Seat Top Assembly, in order to drill holes to match. Use a .281 DIA hole or a size for light press fit to the neck of the "T" Nut [11].
  5. [9] shall be securely fastened to Backing, Seat Assembly [1] and Backing, Back Assembly [2] as shown in Detail A. The neck of [11] shall not exceed the thickness of Backing [7].
  6. See Detail A for typical view showing nails [8] and "T" Nut Assembly [9] used to secure Foam to Backing [7] and to attach [7] to Frame, Seat Top Assembly and Frame, Back Assembly.
  7. Remove all sharp edges of Backing [7] to avoid tearing Vinyl Cover. A .50 radius shall be typical for corners of [7].
  8. Nails [8] shall be driven THRU from underside of Backing [7] to maintain Foam in position during impact.

Parts List:

[1]. Backing, Seat Assembly
[2]. Backing, Back Assembly
[7]. Backing, Cushion, .38 plywood
[8]. Nails, Flat Head, .750 Long
[9]. “T” Nut Assembly
[10]. Washer, Fender, 1.00 O.D.
[11]. "T" Nut, .25-20 NC X .38 Thick

Report a problem with this page

Date modified: